AVR is a series of microcontrollers from Atmel. Fitted with A/D converters, comparators, timers, interrupts, internal oscillator, etc. Flash memory is used for the main program, SDRAM for variables and EEPROM for values that needs to be saved through a power loss. Cheap, fast and easy make them perfect for home automation projects.

Speeds up to 20 Mhz, USART (e.g. RS-232, RS-485) and low power consumption are some other benefits. A starting kit such as the STK500 is a good basis, with this you can test and program a variety of devices.

DSC_018

Getting started

Programming

There are a lot of different IDEs and compilers available, here is a few of them:

Devices

This is some of the devices I most commonly use, for the complete list see Atmels device list:

  • ATmega8
  • ATmega8515
  • ATtiny15
  • ATtiny2313
  • ATtiny26

DSC_007

Basic circuit

basic-avr-attiny2313-circuit-6qjz84

This basic circuit has 7 inputs and 8 outputs and uses a ATtiny2313 with internal oscillator. This is maximum capacity for this device if you don't count PA.0, PA.1 and PA.2, which is normally used for a crystal oscillator and a reset switch.

Try placing C1 and C2 as close to the device as you can, this might improve the stability of the power supply; which is a good thing.

Power

l78s05cv-voltage-regulator-curcuit-0419mq

Most AVR microcontrollers run on 5 volts, which you can easily get by using a voltage regulator and a couple of capacitors. I normally use 47 µF for C1 and C2. A voltage regulator like the L78S05CV can deliver 2 amps and have a maximum input voltage of 35 volts. Remember to mount a heat-sink, especially with high input voltage and/or high load.

External crystal

avr-attiny2313-with-external-oscillator-zgvxl4

If you are going to use an external crystal oscillator it must be connected between XTAL1 and XTAL2 with a 22pF capacitor to GND on both sides. Remember to set the fuse bits according to your oscillator, and if you are going to use serial communication; pick a frequency that works with your baud rate.

I/O

Digital inputs

pull-up-resistor-circuit-kq001q

If your input has a pull-up resistor it will be pulled high when not active. So you need to pull it down (low) to trigger it, meaning that it is triggered by ground. Note that this also inverts your inputs, so you need to handle that in your programming.

pull-down-resistor-circuit-1492eq

When your input has a pull-down resistor it is pulled low when not active and you activate it by pulling it up (high).

Analog inputs

Analog inputs doesn't require pull-ups or pull-downs, they simply measure the input voltage. The value of the input is relative to the AREF (analog reference) pin, meaning that if this pin has 5 volts, and your input has 2.5 volts you will get a value of 512 (half of 1023, which is the maximum of a 10 bit ADC). Remember to power the ADC by connecting it's AVCC and GND pins to power.

To measure higher voltages than the input can handle; you can use a voltage divider, this simply divides the voltage down by using two resistors. And for restive sensors you can use a Wheatstone bridge.

Digital outputs

npn-transistor-amplification-d4wjkq

You can power an LED (20 mA) of the AVR output without any additional components, but any more than that and it's going to need some help. For this we use transistors, a bipolar NPN transistor is a good choice. You will need a resistor on the base pin, otherwise too much current will pass through the transistor and you will break it.

npn-and-pnp-transistor-amplification-wgkwmg

If you are going to drive some heavy stuff a small bipolar transistor is not going to be enough. You need a power transistor, but these do not have the same amount of amplification so it's a good idea to place it after your small bipolar transistor.

PWM outputs can be connected the same way.

Components

LEDs

led-pin-out-4w8vk4

You will pretty much always need a resistor when powering LEDs. Here is a useful tool for calculating the value of that resistor: LED Resistor Calculator.

Useful reading

Transistors

transistor-pin-out-gkdym4

Useful reading

Relays

relay-circuit-gv71lg

When connecting a relay to a digital output it must have a protection diode, this prevents a power surge from flowing back into the input when the relay releases. This surge can cause the microcontroller to restart, it may even break the output.

Diodes

diode-pin-out-qere94

Electricity only flows one way through a diode, just remember that it also has a voltage drop in the forward direction.

Useful reading

Serial

Getting your AVR device to communicate over a serial line opens up a whole new world of opportunities, and is totally bad ass! But; to do that we need some additional components to get our signal levels right. I've added a simple schematic for RS-232 (standard computer serial port) and RS-485 (multidrop communication over long wire spans).

RS-232

avr-to-rs-232-using-max232-ygrz54

With this you can communicate with your AVR device from your computer using the serial port, which is cool.

RS-485

avr-to-rs-485-using-max485-8g2rlq

Now; with this you can build a whole network of AVR devices operating on the RS-485 network, very cool! You will need to handle the addressing in your application though.

Now you are ready for some serious AVR projects! :)

External links